Sink Marks, Flash, Short Shots: Causes and Fixes from the Molding Floor
Name the injection molding defect before you argue about who pays. This guide covers sink marks, flash, short shots, warp, weld lines and burns—typical causes, DFM and process fixes, and what to send in an RFQ.
Direct answer: what injection molding defects really are
When engineers search "injection molding defects," they usually want a name they can put on a trial photograph and a next step—not a catalog of every possible blemish. A named defect points at a family of causes: geometry (walls, ribs, gates), process (fill, pack, cool, clamp), tooling (vents, shutoffs, wear, cooling) or material (grade, moisture, fillers). Arguing about who pays before the defect is named and located is how programs burn a T1 loop.
This guide focuses on the three injection molding defects buyers see most often on first shots—sink marks, flash and short shots—then covers warp, weld lines and burns, which often travel with them. Typical industry starting points below are guidelines, not proprietary JHW laboratory measurements and not a guarantee for every resin, tool and cosmetic class. Confirm each recommendation against the named grade and the written acceptance criteria for that part.
At JHW Molding (Suzhou Jiahongwei Technology Co., Ltd., founded 2016 in Suzhou), we are a one-stop mold and injection project service provider: DFM, mold design review, project management, mold-trial follow-up and outgoing inspection. Mold making and molding run at production partners we manage—we do not claim "our factory" ownership. Partner molding covers about 50T–400T; partners build roughly 50–60 molds a month. Materials commonly molded include PP, ABS, PC, PC/ABS, PA, POM, PMMA, PBT, TPE, TPU, PE, PS and filled grades. Every RFQ includes free DFM; we aim for DFM notes plus a quote in about 48 hours when the pack is complete.
Factory visits and audits are not promised on a cold RFQ. Contact: sales@jhwmolding.com, WhatsApp +86 189 6217 3434. Foreign trade and R&D office: Room 1710, China Automotive Parts Industry Base, No. 19 Aigehao Road, Weitang Town, Xiangcheng District, Suzhou, Jiangsu, China. Production partner (Suzhou): No. 8 Yinyan Road, Suzhou High-Tech Zone. Capability context starts on our injection molding and mold making pages.
Diagnose before you turn knobs: geometry, process, steel or material
Start with a photograph, a marked-up part and the drawing revision that was actually in the tool. Say where the defect sits: show face or hidden, opposite a rib or boss, at the parting line, at the last point of fill, at a knit, at a vent or at an ejector witness. A vague "bad part" comment without a location is not a trial record.
Then split causes into four buckets before anyone leans on the press. Geometry includes thick-to-thin transitions, ribs or bosses that are too heavy, long flow in thin walls, missing draft, and gates on the wrong face. Process includes fill speed, melt and mold temperature, pack and hold pressure and time, clamp, shot size and cushion. Change one family of settings at a time and record it—the same rule as on our page about how to reduce defects. Tooling includes vent depth and location, shutoff condition, cooling balance, gate size, and wear after a previously clean trial. Material includes wet hygroscopic resins (PA, PC, PBT and some polyester grades), a substituted grade, excessive regrind or an inconsistent lot.
If the defect does not move after a documented process window, it is probably steel or CAD. Process can hide a geometry problem for a short run; it rarely deletes that problem for a production life. Write the hypothesis on the trial sheet so the next loop tests one idea, not five at once.
Sink marks: causes and fixes
A sink mark is a local depression on a face, often opposite a rib, boss or other thick section, or in a heavy intersection. Plastic in the thick region shrinks as it cools; if the packing path freezes before that volume is compensated, the skin is pulled inward. On painted or high-gloss faces the depression reads as a highlight; on textured faces it can flatten grain.
Typical geometry drivers are industry starting points to confirm in DFM, not absolute law. Ribs often start around half to about two-thirds of the nominal wall they join—many programs aim near about 50–70 percent, and sometimes tighter on high-gloss or painted show faces, so the rib does not read through. Bosses should not be solid lumps: core them and tie them to a wall with ribs rather than a heavy pad. Core out thick interiors, blend transitions, and keep walls as uniform as the function allows. Filled, foamed or unusually thick technical parts need a part-specific review rather than a copied ratio.
Process and tooling still matter once the geometry is reasonable. Pack and hold pressure and time, a gate that freezes too early (too small or too cold), or cooling that leaves a hot spot opposite the thick feature can all leave sink on an otherwise sound design. Moving a gate so packing can reach the thick region can help when DFM supports it. Raising pack until the part flashes or sticks is not a fix—it trades one injection molding defect for another.
Paint will not hide structural sink. Our guide to painting plastic automotive parts notes that thin high-gloss and metallic films telegraph molding depressions. Fix the wall, the rib and the packing path; do not plan a respray to conceal a thick boss.
Flash: causes and fixes
Flash is a thin film of plastic that escapes the cavity at the parting line, at shutoffs, around slides or lifters, or through vents. A slight witness on a raw hidden shutoff may be acceptable if the drawing allows it. A knife-edge flash on a show face, a sealing edge or a snap fit is usually scrap or a permanent deflash cost.
Common causes include clamp force that is too low for the projected area and the packing pressure; parting faces that are not fully shut (poor spotting, dirt on the split, or a slide that is not home); worn or damaged shutoffs after a previously clean trial; over-packing; vents cut too deep; and a very low-viscosity or overheated melt. Flash that appears after a clean T1 is often wear or process drift. Our mold maintenance note covers vents and shutoffs; steel choice affects how fast abrasive resins wash those edges—see the mold steel selection guide when you plan life and spares.
Fixes start with the tool, not with a slogan. Confirm the mold is clean and fully closed before you chase pressure. Inspect shutoffs and vents. Bring pack back into a window that fills and packs without blowing the split. Repair steel when wear is the root. For new tools, projected area, cavitation and press tonnage belong in the quotation assumptions. Partner molding in the JHW network covers about 50T–400T; a very large projected-area part may sit outside that envelope and should be flagged in the RFQ rather than assumed.
Do not accept leftover flash as a standing habit on a cosmetic or sealing edge unless that secondary trimming operation is written into the piece price and the acceptance criteria. Permanent trimming is a process you are buying, not a courtesy.
Short shots: causes and fixes
A short shot is an incomplete part—the melt froze or lost pressure before the cavity filled. It often shows as a missing corner, an unfilled rib, or a last-to-fill zone that is thin or absent. Photograph the short against the cavity layout so you can see whether it sits at the end of flow, behind a thin wall, or in a pocket that may actually be an air trap.
Causes include a shot size that is too small, insufficient fill pressure or speed, melt that is too cold, walls that are too thin for the flow length, gates or runners that are undersized, and vents that are blocked so air or gas stops the last fill. A blocked-vent short can look like missing plastic and can also scorch; check both. Filled grades raise viscosity and make long, thin flow paths harder. Confirm it is a true short and not a broken fill from a blocked gate or a stuck hot-runner valve.
Design fixes: thicken a starved flow path, add or relocate gates, shorten flow length, or add vents at the last-to-fill and at knit or air-trap zones. At trial: verify shot size and cushion, raise fill speed or melt temperature within the grade window, and confirm vents are open—not just more pressure until flash appears elsewhere. If a thin-wall cosmetic part only fills at the edge of the process window, the geometry is the problem. Capability context for molding sits on our injection molding page; tool construction context on mold making.
Warp, weld lines and burns (and related appearance issues)
Warp is distortion after ejection or after the part cools to a stable temperature. Typical drivers are non-uniform walls and packing, unbalanced cooling, residual stress, and—on glass-filled resins—fiber orientation that shrinks differently along versus across flow. A cooling fixture can sometimes hold a part during cooldown; it does not replace a wall and gate plan. Measure warp the way the drawing intends (free state versus restrained) and say so in the RFQ, or two laboratories will report two different parts.
Weld lines, also called knit lines, form where flow fronts meet. They can be a cosmetic witness and a local strength drop, especially on filled resins or when the fronts meet cold. Gate count and location move the knit; vents at the meeting point help air escape. If a knit must sit on a structural clip or a Class-A face, call that out in DFM before steel is cut. Moving a weld after texture or paint approval is expensive.
Burns—brown or black marks, often at last fill or in trapped pockets—commonly come from compressed air or volatiles that overheat: poor or blocked vents, overly aggressive fill into a blind rib, or moisture and degradation in the resin. The fix is venting, fill-speed control, and proper drying of hygroscopic grades—not polishing a scorch off a show face. Related appearance issues such as splay or silver streaks from moisture or degradation, and jetting from a poorly aimed gate, belong in the same trial log even when they are not in the title of this page.
Drag marks from short draft are release defects, not fill defects. Process rarely replaces missing taper on textured walls; see draft angle in injection molding for typical ranges and texture rules.
What to fix in CAD versus what to try at T0 and T1
T0 is for fill, stuck parts, obvious steel issues and a first look at flash, shorts and burns. T1 is for dimensions and cosmetics against written criteria after those corrections. T2 is another loop if T1 missed the written list. Labels vary by shop; define the purpose of each trial in the purchase order—see our T0 / T1 / T2 trials note.
A useful trial rule: change one family of settings at a time, photograph each loop, and record melt and mold temperatures, fill and pack, clamp, and material lot and dryness. If sink opposite a heavy rib does not move after a documented pack window, thin the rib or core the boss in CAD. If flash returns after a shutoff repair and a stable process, look at projected area, press capacity or packing intent. If a corner only fills at the edge of the process window, redesign the flow path.
Do not use trial loops to invent a new cosmetic standard. Acceptance criteria for sink visibility, allowable flash length, knit visibility and burns should be written before you argue about a borderline sample. Outgoing inspection at JHW follows the criteria you agreed—not an unpublished house slogan of "zero defects." We coordinate trials at production partners under project management and outgoing inspection; we do not claim factory ownership. For how records and lot criteria should be written, see our quality control guide.
DFM and RFQ tips for injection molding defects
Send STEP (preferred) plus a drawing revision, resin grade or family, annual and first-order quantity, and a map of cosmetic versus functional faces. Mark sinks that would be unacceptable, faces that cannot show flash or vestige, and structural features that cannot sit on a knit if that matters.
Call out wall targets, texture or paint, and whether you already have a preferred gate side. Free DFM with every JHW RFQ is where we flag thick sections, risky ribs and bosses, vent and last-to-fill concerns, and likely flash or short-shot risks before steel is cut. Start from the DFM checklist and the note on how to design plastic parts; a scoped DFM review is also available when you want a written risk list before you award the tool.
From JHW you should expect DFM notes plus tooling and piece-price lines when the pack is complete. Target turnaround is about 48 hours for a complete pack. Office: sales@jhwmolding.com, WhatsApp +86 189 6217 3434. Foreign trade and R&D office: Room 1710, China Automotive Parts Industry Base, No. 19 Aigehao Road, Weitang Town, Xiangcheng District, Suzhou, Jiangsu, China. Production partner (Suzhou): No. 8 Yinyan Road, Suzhou High-Tech Zone. Start from the quote page when your file pack is ready. Automotive interior programs can also use the automotive injection molding and automotive interior pages for capability context.
FAQ: injection molding defects
Q: What are the most common injection molding defects on first shots? A: Sink marks, flash and short shots show up often, along with warp, weld lines and burns. Name the defect and its location before you change process or steel.
Q: Can process settings alone fix sink marks? A: Pack and cooling can reduce mild sink. Heavy ribs, solid bosses and thick-to-thin transitions usually need geometry changes. If sink is unchanged after a documented pack window, fix the CAD.
Q: Is flash always a process problem? A: No. Flash can be clamp, over-pack, worn or dirty shutoffs, vents that are too deep, or a tool that is not fully closed. Flash after a previously clean trial often points at wear or drift.
Q: How do I tell a short shot from a burn or an air trap? A: A short is missing plastic. A burn is a scorch mark, often in a last-to-fill pocket. An air trap can cause either or both. Check vents and whether the unfilled zone is truly empty or scorched.
Q: Do you claim ISO 9001, IATF 16949 or publish proprietary defect-rate data as JHW measured results? A: We do not claim certifications on this site, and we do not present proprietary measured defect rates as law. We use industry-typical diagnosis and confirm geometry, process and tooling against your part in DFM and trials.
Q: Can I visit the production partner or audit the toolroom on a cold RFQ? A: Visits and audits are not promised on a cold RFQ. If your program requires an on-site path, state it early so commercial and schedule assumptions stay honest.
Q: How fast can I get DFM that flags likely injection molding defects? A: Every JHW RFQ includes free DFM. We aim to return DFM notes plus quotation within about 48 hours when STEP or drawing, resin, quantities and cosmetic notes are complete.
Q: How do I RFQ with defect and cosmetic criteria? A: Send STEP, resin, volumes, a cosmetic map and any written limits on sink, flash, knits and burns to sales@jhwmolding.com or WhatsApp +86 189 6217 3434, or start from the quote page.